Components And Technical Specs

Components and Specifications
Operation Control
Boxing Options

Components and Specifications

Headbox back

Headbox front

End plate

Axle Assembly

Spring

Skin

Channel

Slide Track

Bottom Bar Assembly

Ezylift Latch

TRACKING SYSTEM

Our tracking system is a patented extrusion, engineered to restrain outdoor blind skins with welded splines.
The channel runs inside the track gives the cleaner finish which avoid ugly tracking effect.
Concealing the spline within the tracks and hiding the weld from view when installed.

Brackets & Channels

BRACKETS

Brackets are available to support the top tube in situations where boxing is not suitable.

The top tube locators can be dropped into the brackets, which must be fitted to allow enough room for the fabric to build up around the roll.

It is important to consider when selling brackets without boxing that, when the skin is rolled down, there is an open gap left above the top tube.

EXTRA DEEP (GEARBOX) CHANNEL

21mm deeper than standard. Developed to accommodate the extra width of a gearbox.

STANDARD CHANNEL

The most commonly used channel, at 23mm deep, you simply fix the channel to the application surface & sit tracks in place.

Each channel has +/- 5mm built-in adjustment. When happy with the blind’s operation, fix track to channel. If surface is square and measured correctly, there should be 5mm of channel visible when looking at the front of the blind.

SMALL COLUMN CHANNEL (OR CURVED CHANNEL)

For fixing to columns smaller than 200mm. For larger diameter columns a standard channel can be used. Simply fix to column, taking care not to over-tighten, as this may bend the channel edges out of shape.

TECHNICAL SPECIFICATIONS

Maximum Width	5500mm
Maximum Height	3000mm
Maximum Area	(m2) 16.5
Headbox Size	145mm x 150mm high
Bottom Bar Size	25mm x 70mm wide
Control Options	Spring, Crank or 12v Motorised

REVEAL FIX

1. Accurately measure the top of the opening. Look for the narrowest point where the hood will be slid in and where it will be mounted. We will make the hood 2mm narrower than your advised top opening.

2. Measure the centre and bottom openings and record.

3. Check both sides to see if they are level horizontally. Make a note on your order if a side is out by more than 10mm.

4. Measure the drop from the top of the opening to the ground.

FACE FIX

1. Measure the points at which the headbox will be fitted, outside of headbox to outside of headbox, and record as the top measurement.

2. Normally the centre and bottom measurements are the same.

3. Measure the drop from the top of the required hood position to the ground.

* For a single opening, we recommend adding 55mm to each side of the opening measurements (110mm overall) for final width measurements. This will keep the fixings for mounting the face fix angles away from the corners for strong fixing points and so that the tracks will not be visible from the inside of the opening.

* For multiple adjacent openings, pairs of blinds can be measured to meet against a single face fix angle, effectively butting up together with channels fixed back to back on either side of the angle.

Motorised

OZROLL E-SOLARPRO WITH ODS T-SERIES MOTORS

The E-SolarPRO is a sleek module which collects energy from the sun through the solar panel andstores it in the battery located in one end of the module. Using an Ozroll E-Trans Remote, the stored energy operates the ODS T-Series 12v motor with the press of a button. The E-SolarPRO offers a standalone motorised system without a need for mains power.

* E-SolarPRO must be fixed in a position where direct sunlight can be received.

The E-Port 18650 Standard or RF controls with the T-Series motors are another stand alone option for controlling the Slidetrack Window Blinds and Verandah Screens. As with the E SolarPRO an electrician is NOT required for installation and the motors are driven by the power from the Lithium-Ion batteries in the controls. The E-Port 18650 RF control works with a 1 or 9 channel hand-held remote.

240V ELECTRIC MOTORS

Hardwired 240v Electric motors are available in either standard with a fixed wall switch or an RTS version operated by a 1ch or 5ch handheld remote.

Solar Powered
Battery Operated
Remote Controlled

E-TRANS 1 CH OR 9CH

E-PORT 18650

E-PORT 18650 RF

INIS UNO WALL SWITCH

5 CH HAND HELD REMOTE

MANUAL

SPRING ASSIST WITH EZYLIFT

The manual Spring Assist option is a common choice for Outdoor Blinds across Australia, however Slidetrack's unique Ezylift handle design provides premium strength with effortless operation.

GEARBOX

Gearbox operation is a traditional system, whereby the user manually raises the blind with a cranks handle which hooks into an eye outlet. This type of control must be fitted with extra deep channels.

SPRING WITH BOLTS ON THE BOTTOM BAR

Box Type	Maximum Height Motorised or Gearbox	Maximum Height Motorised or Gearbox	Maximum Height Manual	Maximum Height Manual
	MESH	PVC	MESH	PVC
145 Extruded	3200	3100	3100	3000
150 Roll Formed	3500	3300	3300	3200
Mounted In Brackets	3500	3500	3500	3500

145MM EXTRUDED ALUMINIUM HEAD BOX

It is extruded head box is a two-piece pelmet produced with cast aluminium and finished with specialist end caps.

This fully enclosed head box offers a unique smooth shape

Industry leading strength due to thickness of material. Tested on blinds as wide as 6600mm, this is the ideal option for wide spans or for powder coating, when trying to avoid warping or bowing.

150MM ROLL FORMED ALUMINIUM HEAD BOX

We use well engineered roll formed head box is a two-piece pelmet in our blinds

Ozroll’s square roller shutter end plates have been adapted to support the Unique Slidetrack top tube

The fully enclosed head box which protects the rolled up skin, option offers a conventional look at a cost effective price.